Brite Alum acid-based cleaner to restore and brighten condenser coils

Brite’ Alum BA- 1, 5, 55

BRITE ALUM – is an acid-based condenser coil cleaner that cleans and brightens with deep penetrating foaming action. Specially formulated to remove scale, oxides, and contaminants. Original heat transfer capabilities are restored, resulting in improved efficiency and lower energy bills. Coils are left shiny and like new. It may also be used on electronic air filters. One gallon makes 4 gallons of ready to use coil cleaner. Rinsing is required. VOC content is zero

BRITE ALUM

Restore Your Condenser Coils to Like-New Condition

BRITE ALUM is a powerful acid-based cleaner designed to revitalize condenser coils. Its thick, heavy-foaming formula penetrates deep into coils to remove scale, oxides, and contaminants, restoring original heat transfer capabilities.

Key Features and Benefits:

Acid-Based Cleaning: Effectively removes stubborn deposits.
Cleans and Brightens: Leaves coils shiny and clean.
Deep Penetrating Foam: Reaches deep into coil crevices.
Removes Scale and Oxides: Restores original heat transfer efficiency.

Improved Efficiency, Lower Energy Bills: By restoring heat transfer, BRITE ALUM can help reduce energy consumption and lower your utility costs.

Versatile Application: In addition to condenser coils, BRITE ALUM can also be used to clean electronic air filters.

Concentrated Formula: One gallon of BRITE ALUM makes four gallons of ready-to-use coil cleaner, providing excellent value.

Zero VOC Content: Environmentally friendly and safe for use.

Restore your condenser coils to peak performance with BRITE ALUM. Enjoy improved efficiency, reduced energy costs, and a cleaner, healthier indoor environment.

Part Number; Size

BA-1 1 gal 4/cs
BA-5 5 gallons
BA-55 55 gallons

Safe and Effective Coil Cleaning

Before Use:

Consult SDS: Refer to the Safety Data Sheet (SDS) for detailed safety information.
Wear Protective Gear: Always wear goggles, gloves, a face shield, and protective clothing.

Application:

Power Off: Turn off the HVAC system.
Dilute: Mix 1 part BRITE ALUM with 3 parts water. Avoid using undiluted.
Spray: Apply the diluted solution directly to the coil using a low-pressure Vapco tank sprayer. For multi-coil units,repeat spraying as needed.
Rinse: After 3-5 minutes, thoroughly rinse the coil.

Important: Keep the solution from freezing for optimal performance.

By following these instructions and using BRITE ALUM, you can effectively clean and maintain your condenser coils.

DANGERS & PRECAUTIONS

Read and understand the product’s label and Safety Data Sheet. Do not breathe mists. Wash hands and gloves thoroughly after handling.

News and Updates

Subscribe on Youtube

SDS

BRITE ALUM SDS REV. 1

Safety Data Sheet – Brite Alum

Vapco Products, Inc.

Identification & Supplier Details (SDS Section 1)

Product Information
Product Name / Identifier	Brite Alum (BA-1, BA-5, BA-55) / Brand: Vapco
Recommended Use	Acid-based condenser coil cleaner
Supplier Details
Name & Address	Vapco Products, Inc. / 401 Marshall Road, Valley Park, Missouri 63088, United States
Contact Information	Tel: (636) 923-2121 \| Fax: (636) 923-3002 \| Email: [email protected]
Emergency Phone Number	(800) 255-3924

Hazard Identification & Composition (SDS Sections 2 & 3)

Classification & Labeling
GHS Classification (OSHA)	Acute toxicity (Dermal, Oral, Inhalation), Cat. 1/2; Skin Corrosion/Irritation, Cat. 1A; Eye Damage/Irritation, Cat. 1
Signal Word / Pictogram	Danger /
Hazard Statements	H300: Fatal if swallowed. H310: Fatal in contact with skin. H314: Causes severe skin burns and eye damage. H330: Fatal if inhaled.
Key Precautionary Statements	P260: Do not breathe vapors/spray. P262: Do not get in eyes, on skin, or on clothing. P310: Immediately call a POISON CENTER/doctor. P284: In case of inadequate ventilation, wear respiratory protection.

Hazardous Component	CAS No.	Concentration (wt)
hydrofluoric acid 49% (HF)	7664-39-3	5 – 15 %
1-Propanaminium, N-(3-aminopropyl)-2-hydroxy-N,N-dimethyl-3-sulfo-, N-coco acyl derivs., hydroxides, inner salts	68139-30-0	1 – 10 %

Physical & Chemical Properties (SDS Section 9)

Property	Value
Physical State / Appearance / Color	Liquid / Cloudy liquid / Pink
Odor / Odor Threshold	Acid odor / N/D
pH	< 1 (Strongly Acidic)
Melting Point / Freezing Point	< 32°F (0°C)
Flammability / Flash Point	Not considered a flammable liquid by OSHA / N/D
Density and/or Relative Density	1.02 at 77°F (25°C)
Vapor Pressure / Evaporation Rate	23.8 mmHg at 77°F (25°C) / < 0.8 (Slow)
Solubility	Soluble in water
Volatile Organic Compounds (VOCs)	< 1%

Stability & Reactivity (SDS Section 10)

Factor	Condition / Material
Reactivity / Chemical Stability	May react with strong bases and chemically active metals. / Stable under normal conditions of use.
Conditions to Avoid	Chlorine-liberating material. Do not mix with bases, ammonia or other cleaning compounds. Excessive heat/Direct sunlight.
Incompatible Materials	Strong bases and chemically active metals.
Hazardous Decomposition Products	Carbon oxide(s), nitrogen oxide(s), and metal oxide(s).

Toxicological Information (SDS Section 11)

Endpoint	Summary
Acute Toxicity (ATE – Mixture)	Oral: 33.33 mg/kg bw (Fatal if swallowed) \| Dermal: 33.33 mg/kg bw (Fatal in contact with skin) \| Inhalation (Mist): 0.33 mg/l (Fatal if inhaled)
Skin Corrosion/Irritation	Causes severe burns, prolonged contact will destroy tissue.
Serious Eye Damage/Irritation	Causes severe burns, irritation, redness, tearing, pain, and may result in loss of sight.
STOT – Single/Repeated Exposure	Causes severe burns (single). Chronic symptoms include possible liver, kidney, and blood damage due to long-term exposure.
Carcinogenicity / Mutagenicity / Reproductive Toxicity	Not classified.

First-Aid Measures (SDS Section 4)

Exposure Route	Action Required
General Advice / Emergency (P310)	If you feel unwell, Immediately call a POISON CENTER/doctor. Specific treatment is urgent (P320). Have product container or label at hand.
Inhaled (P304+P340)	Remove person to fresh air and keep comfortable for breathing. Get medical advice/attention immediately. (Ensure rescuer safety first).
Skin Contact (P303+P361+P353 / P302+P352)	Take off immediately all contaminated clothing. Rinse skin with water/shower for at least 15 minutes. Wash contaminated clothing before reuse (P363). Immediately obtain medical attention.
Eye Contact (P305+P351+P338)	Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately obtain medical attention.
Swallowed (P301+P310, P301+P330+P331)	Rinse mouth. Do NOT induce vomiting. Immediately call a POISON CENTER/doctor.

Fire-Fighting & Accidental Release Measures (SDS Sections 5 & 6)

Measure Type	Details
Suitable Extinguishing Media	Water spray, fog, carbon dioxide (CO₂), alcohol-resistant foam, dry chemical, or sand. (Use media appropriate for surrounding fire).
Specific Hazards	May be corrosive to metals and reactive to strong bases. Hazardous Combustion Products: Carbon oxide(s), nitrogen oxide(s), and metal oxide(s).
Protection During Fire-Fighting	Wear NIOSH-approved Self-Contained Breathing Apparatus (SCBA) with full face piece operated in a positive pressure demand mode and full body protective clothing.
Accidental Release Precautions (P260, P262)	Do not get in eyes, on skin, or on clothing. Do not breathe vapors/spray. Use appropriate PPE. Eliminate ignition sources, isolate, and ventilate the area.
Containment & Clean-up	Contain any spills with dikes or absorbents. Take up liquid spill into absorbent material. Transfer to a suitable container for disposal.

Handling, Storage & PPE (SDS Sections 7 & 8)

Area / Equipment	Requirements / Controls
Safe Handling Precautions (P264)	Do not handle until all safety precautions are understood. Avoid contact with skin/eyes/clothing. Wash hands thoroughly after handling.
Storage Conditions (P405, P403+P233)	Store locked up. Store in a dry, cool, well-ventilated place. Keep container tightly closed. Do not expose to temperatures exceeding 50°C/122°F. Incompatible Materials: Strong bases and chemically active metals.
Exposure Limits (Hydrogen Fluoride, CAS: 7664-39-3)	IOELV-LTEL: 1.5 mg/m³ (1.8 ppm) \| IOELV-STEL: 2.5 mg/m³ (3 ppm)
Engineering Controls	Emergency eye wash fountains and safety showers should be available. Ensure adequate ventilation. Use explosion-proof equipment.
Eye/Face Protection (P280)	Chemical safety goggles.
Skin/Body Protection (P280)	Wear protective gloves (chemical resistant materials) and suitable protective clothing.
Respiratory Protection (P284)	Use a NIOSH-approved Self-Contained Breathing Apparatus whenever exposure may exceed established OELs.

Transport & Regulatory Information (SDS Sections 14 & 15)

Transport Mode	UN Number	Class (PG)	Proper Shipping Name
DOT (US) / IMDG / IATA	UN2922	8 (6.1) (II)	Corrosive liquids, toxic, n.o.s

U.S. Regulatory Information
TSCA Inventory	hydrofluoric acid 49% (7664-39-3) and other component(s) are listed.
State Right-to-Know Components	Hydrofluoric Acid (7664-39-3) is listed on Massachusetts, New Jersey, and Pennsylvania Right-to-Know lists.

Disposal & Ecological Information (SDS Sections 13 & 12)

Area	Guidance
Waste Treatment / RCRA	Check the pH of the waste to be disposed. May be subject to disposal regulations: U.S. EPA 40 CFR 261. Hazardous waste number(s): D002 (Corrosivity).
Product Disposal (P501)	Dispose of contents/container in accordance with local, regional, national, and international regulations.
Persistence and Degradability	This product is biodegradable.
Bioaccumulative Potential / Mobility	Not expected to bioaccumulate. Product is mobile in soil.

Disclaimer & Preparation Information (SDS Section 16)

Disclaimer:

To the best of our knowledge, information contained herein is accurate. However there is no assumption of liability for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. The information contained in this SDS was obtained from current and reliable sources; however, the data is provided without warranty, expressed or implied, regarding its correctness or accuracy. Since the conditions of handling, storage and disposal of this product are beyond the control of the manufacturer, the manufacturer will not be responsible for loss, injury, or expense arising out of the products improper use. The user is responsible for full compliance with all government regulations.

N/A = Not applicable; N/D = Not determined

Prepared by: Jessica Wilson, Date prepared: 3-10-2025

Brite’ Alum BA- 1, 5, 55

BRITE ALUM